The article author is making a few great annotation on A Step-by-Step Guide to Installing a Bathtub in general in this article on the next paragraphs.
Installing a tub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a reasonably tough task. If the old bathtub is conveniently available, the project can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the work and also fit attempting it. Rather than working with a service provider to take control of a halfway-completed task, it is much better to consider utilizing one prior to you begin. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have already acquired a new tub as well as do not require to transform the setup of your previous water system pipelines.
Your devices and product list should make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, activate the faucets to drain any kind of water staying in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in area between the faucet as well as the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The former type must be attached to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the called for position. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the water system as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been utilized at least when as this will resolve it into its final position.
Planning for the Installment
First of all, the supporting structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with moisture and also possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when surfing the search engines. Enjoyed reading our posting? Please share it. Help someone else discover it. Thanks a bunch for your time. Visit again soon.
This Post